arrive customer service
The Bill of Materials, or B.O.M., is the number stamped on the right or left hand tube of the axle. a Right Hand Shaft Assy number), return to the Dana 60 Front Axle Bible, and use the links there to open the various Dana Spicer catalogues in .pdf format. number. The axles on a Dana 50 taper from 1.5 inches to 1.31 inches where it goes into the carrier. In the back they will have a Dana 60. Just look at the backing plate bolts. While you can look up the serial number on a Dana 60 to figure which axle it is, there’s a pretty simple trick for telling if the axle came out of a Chevy, Dodge, Ford, GMC, or Jeep. it has an aluminum center section, with 30 spline axle shafts. I would like to put in my 1965 chevelle if it will fit. We will assume it is a 10-bolt – but that makes it a plenty strong 8.5-inch ring gear diameter – not the 8.2-inch. The most important is the model, or service code, found in the upper-left corner. The major marks are the axle assembly stamp and the carrier casting number and casting date code. Note the way the ends are made for spindles. I recently purchased an 8 lug dana 44 from somebody on this board for my K5 Blazer. DANA 4360 View and Download DANA 4360-140 parts list online. Still, the 14 bolt semi-float is a solid axle for a lot of applications. Go to www2.dana.com and look it up to see what you’ve got. The top line typically starts with a three-digit axle model code (or the prefix of the part number), followed by a dash, and then the suffix. I only have data going up to 1997 so if you can add to this list it would be greatly appreciated. 6. They have a ring gear diameter of 7 and 1/8 inches. Crown Automotive 53007463 Axle Wheel Stud for 90-95 Jeep Wrangler YJ, 97-99 & 03-06 Wrangler TJ, 90-99 Cherokee XJ & 93-98 Grand Cherokee ZJ - 97-99 With 2 Piece Composite Rotor Item: 52428.04.14 MFG#: 53007463 The model number and date are self explanatory. The number is cast into the webbing next to the pumpkin and is also listed on the tag if your axle still has one. The Spicer Independent Rear Suspension assembly is identified by numbers which are stamped on the carrier. If you have access to axle tag codes for '72-up, please e-mail me. Service and Parts Manual. Early Ford Beam Axle Identification and Dimensions; How To Box-In a Differential / Solid Axle Rear-End Housing; How To Decode Ford Part Numbers; How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch Rearend The fronts have the changes needed for spindles, while the rear ones allow for the axles to accept bolt-on wheels. Hence, the birth of the Dana 61, which has a different casting that moves the pinion over 0.25"-0.437" (conflicting reports) - this allowed for a 3.07 axle ratio. The cover is about 9" wide about 9-9 1/2 tall, 2 1/2" axle tubes the the casting numbers threw me. The posi manufacturer codes are D for Dana, E for Eaton, and W for Warner. Obviously, the ring gear is 8.75 inches in diameter. PINION BEARING SHIMS; Fits CHEVY GMC K5, K10, K20 all with DANA 44 Front Differential; Fits DODGE D500, D600, D800 with DANA 44 Disconnect front axle SK F8 - Pinion depth shims for Ford 8-Pinion depth shims for Ford 8 8 Ford pinion shim kit. The number on the top left of this sticker in 610366-8. Click on the thumbnail to enlarge the image Front Axle Dana 25 & 27 Quantity: 3.3L (6.9 pints) 2 – Axle model identification 3 – Specification number assigned to the axle built by Spicer. These tool numbers are numbers of Miller Special Tools, 32615 Park Lane, Garden City, MI 48135. The numbers across the top are gear ratios, the numbers down the left side are tire sizes in inches, and the 4 digit numbers in the white boxes show RPM. Introduction: The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of vehicles. Order before 4PM and most parts ship out the SAME DAY! Wranglers that are equipped with the Rubicon package typically come with the 4.10 gear set in their Dana 44 axles. The Casting number is: C32192. Ten bolts retain the carrier, and the pinion spline can be either 10-spline or 29-spline. Front Differential F-250/350 Dana 50 axle. Messages: 28. The Dana LMS™ hub design combines proven seal technology with precision-manufactured bearing spacers and special tolerance bearings. Drive Axles 1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. To have an image removed from this website, please contact us at: info@differentials.com is in reference to this. Get a direct bolt-in solution that delivers increased strength wherever you take your vehicle. Identification of these rear ends is pretty straightforward. Go to: Differential Tags Information about Differentials in GM vehicles can usually be obtained by looking at the RPO or “Regular Production Option” codes contained in … Jump to Latest Follow ... you could have the Dana 44a rear axle. Go to www2.dana.com and look it up to see what you’ve got. I think. The Dana 61 also uses 3.5" axle tubes. Click on the thumbnail to enlarge the image Front Axle Dana 25 & 27 The Borg Warner Spin Resistant unit can be recognized by its lack of bolts on the side opposite the ring gear (like the Dana), and two openings exposing the preload springs. it has a spicer transaxle model 4360-212CH and the input shaft bearings had gone bad, chewed up the top case a little. The Dana Power-Lok can be recognized by its bolt-together assembly, bolts around the side opposite the ring gear, and multiple openings exposing the cross shafts. I have gm axle “cx0824” 389914 Nwaww. This Dana 70HD rear axle assembly came out of a 1976 E-350 cargo van, if my memory serves me correct. Dana 30: This axle size is the most common, and you'll only find it on the front of Jeep. Obviously, the ring gear is 8.75 inches in diameter. 1 ton's (D/W 300 and 350's) will be a Dana 60 up front and either a Dana 60 or 70 in the rear. Starting in 1972, modern factory Dana 44's had 30-spine axle shafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline). The production or service part number of the carrier assembly. The metal tag has four different sets of numbers, each grouped in the four corners of the tag. axle identification. The axle bearings are: 25590 (Timken cone), and 25520 (Timken cup), (Chrysler numbers 1790523 and 696403). I have been told but not confirmed that GM only used the dana 44 3/4 ton through 1979. Throughout the manual reference is made to certain tool numbers whenever special tools are required. The OEM part number assigned to the axle build. Part numbers listed are original Willys part numbers and may have been replaced with a more updated number. Dana makes no warranty or representation to these tools. The 70-U uses a smaller pinion bearing than any of the others (the same as a 60) All the others use the same inner pinion bearing. For the latest product additions and program details, visit us on the web at www.spicerparts.com. It has bolt in axles. Starting in 1972, modern factory Dana 44's had 30-spine axle shafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline). Type: Motorcraft SAE 75W-90 Premium 4x4 Front Axle Lubricant. The spec number will identify all the component parts of the axle as built by Spicer, including special OEM requirements such as yokes or flanges. … Part numbers listed are original Willys part numbers and may have been replaced with a more updated number. The width of the axle shafts is 1.13 inches. ... TOYOTA MOTOR CORPORATION, OR FORD MOTOR COMPANY. I tried to … AXLE IDENTIFICATION Figure 4 5329-4 All Spicer axles are identified with a manufactur ing date and the complete part. The differential axle bearings are: LM 104912 (Timken cone), and LM 104949 (Timken cup), (Chrysler numbers 2852729 and 2852728). Other than that, it is very similar to the Dana 60. It will help ensure an exact replacement and / or that the correct parts are provided. 95 if over *contiguous 48 states Use this book to order parts for your Dana ® … On all Spicer carrier type axles the manufacturing date and Bill of Material number are stamped on the right or left tube for identification and model number stamped on the casting. I am also not sure of the tube size, should it be a 2 1/2". After awhile you get good enough at it that you don't need it, but it is a great tool for those of us that are not there yet. Code Year Model Ratio Type of Drive NL or L Spicer Axle Model Additional Information; C0TT-J '60-62: P-350: 4.88-NL: 44-6- Fusion Hybrid 60/44 Front AxleHigh Clearance off-road center sectionUtilizes Dana 60 lockers, gears, and 35 spline axle shaftsMassive 3.5" diameter tubes with 7/16" wallHeavy duty forged JK inner knuckle Cs65.5" Width (same as stock) Heavy duty 1/4" laser cut and CNC bent bracketsDesigned and manufactured in the USAAvailable in custom widths as well as custom caster and pinion anglesThe … The 1962-63 serial numbers are located on the front, right side of the differential carrier. 1972 to 1975 would have a Dana 60 rear axle and Dana 44 HD front axle with part-time and drums. 1997 3500 club cab 3.54 gears towing & camper pkg. Pinion depth is adjusted by adding or subtracting shim thickness. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. The illustration below will help identify the Dana Axle in your Jeep. The 1962-63 serial numbers are located on the front, right side of the differential carrier. Identifies all component parts of the axle including special OEM requirements such as yokes or flanges. Carrier bearings and outer pinion bearing are the same as a 60. Axle model identification 3. Compared to the 14 bolt full-float axle, the 14 bolt semi-float has a smaller ring gear (9.5″), and the axle shaft can not be removed without also removing the wheels. How To Identify A Spicer Axle All Spicer Carrier Type axles are identified with a manufacturing date (1) and Bill of Material number (2) stamped on the right or left hand tube on driving axles. The chart below shows the relationship between gear ratios and tire size. AXLE IDENTIFICATION Figure 1-1 Spicer axles are identified with a manufacturing date and complete part numbers stamped on the right-hand tube. They are used herein for customer convenience only. Drive Axle Model Identification • Tag 2 (Australian) • Model Number • Part Number • Serial Number • Ratio • Date • AU = Ratio changed at Dana Australia • Drive Axle Model Identification • All Spicer heavy axle carriers are identified by either one of two tags. 2. The Model Identificationnumber provides important vehicle, capacity and application informationand model features. Looking at the axle sticker, we see on the top left Dana P/N 610659-1. Dana 30 axles can be identified by their 10 cover bolts (five on top, five on bottom), oval cover shape with flat sides and a fill plug just below the axle center line and a “30” cast into the back of the differential casing on the top right and top left of the diff cover. Right now my jeep has a ford axle and has a GP part number cast in it. 5. Other than that, it is very similar to the Dana 60. Dana Spicer 5-260X 260X Series U-Joint for 76-86 Jeep CJ, 87-95 Wrangler YJ & 84-99 Cherokee XJ with Dana 30 Front Axle without ABS - AFTERMARKET UPGRADE! SGDTT6ESWD0335379 – first two characters = Country of manufacture (SG in this case represents UK) SGDTT6ESWD0335379 – 3rd character = Can vary but in most cases is the make (B for Bailey, A for Avondale etc) SGDTT6ESWD0335379 – 4th character = Whether the caravan is sible or … Do you have a Dana 60 axle, but you’re not sure whether it’s built for a GMC/Chevy/Jeep, Dodge, or Ford vehicle? The 70-U uses a smaller pinion bearing than any of the others (the same as a 60) All the others use the same inner pinion bearing. The 1964 serial numbers are found on the bottom of the carrier. Need your help please. Some axles may also include an identification tag as shown. PINION BEARING SHIMS; Fits CHEVY GMC K5, K10, K20 all with DANA 44 Front Differential; Fits DODGE D500, D600, D800 with DANA 44 Disconnect front axle SK F8 - Pinion depth shims for Ford 8-Pinion depth shims for Ford 8 8 Ford pinion shim kit. The C-washers for axle retention are 4N237, axle brackets are 4A263, and even the differential bearing shims are 4A451. • Axle Model Identification, Part Number and Serial Number are located on a tag at the axle cent erline. If you need Here's a front Dana 44 cover from Rancho, an RS-6209. This information will help to locate information in this book and to identify the correct parts for servicing. The front is an AAM 9.25 and the rear is a hybrid AAM 10.5 with the larger axle shafts from the AAM 11.5. Jump to Latest Follow ... for dana axle identification but my problem is that the previous owner changed the dually axle to a swd and there is no identification number on the place they supposed to be on the differential. Help identify my dana 44. 4 – OEM part number assigned to the axle build 5 – Carrier assembly serial number assigned by the manufacturing plant 6 – Axle gear ratio number. Despite the fact the axles have locking differentials, the rear axle is also a helical-type limited-slip differential when unlocked. Rear Axle Assembly Codes The rear axle ratio may be determined by finding the two- or three-letter serial number prefix in the following table. The Dana axle identification BOM’s are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. Despite the fact the axles have locking differentials, the rear axle is also a helical-type limited-slip differential when unlocked. New or Hot Selling Items. Identifies all component parts of the axle including special OEM requirements such as yokes or flanges. Dana makes no warranty or representation to these tools. It could be a 10- or 12-bolt. I know this is a really old thread, but it comes up often during a search for Dana 60 BOM numbers so hopefully this information will be helpful to others doing the same search. Later-model Dana axle identification charts may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1. I belieeve this is a dana 80, can anyone confirm? The only identifying numbers that I can find are D60 stamped into one web of the differential and the number C-30255 or maybe it's 0-30255 stamped into another web. Model Identification Drive Axle Parts Identification Axle Housing Axle Shaft 1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. The most important is the model, or service code, found in the upper-left corner. The Dana 44s have 10 bolt holes. Another set of basic numbers is reserved for body components and yet another set for service tools, but we are focused on the axle and driveshaft for the purposes of this book. Crown Automotive 53007463 Axle Wheel Stud for 90-95 Jeep Wrangler YJ, 97-99 & 03-06 Wrangler TJ, 90-99 Cherokee XJ & 93-98 Grand Cherokee ZJ - 97-99 With 2 Piece Composite Rotor Item: 52428.04.14 MFG#: 53007463 i believe only aussies are available as lockers. Ten bolts retain the carrier, and the pinion spline can be either 10-spline or 29-spline. The major marks are the axle assembly stamp and the carrier casting number and casting date code. The Borg Warner Spin Resistant unit can be recognized by its lack of bolts on the side opposite the ring gear (like the Dana), and two openings exposing the preload springs. Early Ford Beam Axle Identification and Dimensions; How To Box-In a Differential / Solid Axle Rear-End Housing; How To Decode Ford Part Numbers; How To Install a Limited Slip/Posi Unit in a GM 10 Bolt 8.5″ Rear-end; How To Install Ring and Pinion Gears in a Ford 8.8 Rear-End; How To Narrow a Ford 8.8 Inch Rearend Spicer Axle Parts Book 2 Spicer Axle Parts Book Corporation, presents this Parts Book as an aid in the identification and procurement of replacement parts for Axles. This will help identify the parts needed out of a Spicer catalog. West Coast Differentials stocks a complete line of light duty axle parts for Chevrolet, Chrysler, Dana, Ford, GM, Jeep and Toyota and more! The number in the name (Dana 30, Dana 44, etc.) number identifies all components of the axle as built by Eaton, including OEM special requirements such as yoke or flange. The format has changed over the years but mostly follow this sequence:. Cleaning with a wire wheel is not recommended as it usually makes the numbers harder to see *** … These numbers are small but they are always on original axles. The production or service part number of the carrier assembly. The illustration below will help identify the Dana Axle in your Jeep. Drive Axles Drive Axle Assembly Tag 1. 4. • Axle Model Identification, Part Number and Serial Number are located on a tag at the axle centerline. This information will help to locate information in this book and to identify the correct parts for servicing. These tool numbers are numbers of Miller Special Tools, 32615 Park Lane, Garden City, MI 48135. The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. 75 in - Kit. Differential & Axle Parts Specialists We have your differential parts in stock ready to ship today. The Axle Model Identification number contains information that is important to understandwhen purchasing service parts or new components. Locate the axle ID tag on the rear-end housing---usually a sheet-metal tag bolted to the housing, although some vehicles had a paper tag, which may be missing. Rear Axle Numbers The third major drivetrain component, the rear axle/differential, like the engine and transmission, was also marked for identification. Drive Axles 1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. 95 if over *contiguous 48 states Use this book to order parts for your Dana ® … Use this guideline to understand your Axle Model Identification. • Axle Model Identification, Part Number and Serial Number are located on a tag at the axle centerline. I know that when I am ass deep in the junkyard and everything has 2 inches of gunk on it and I have been looking at axles for hours on end this little baby comes in handy. The Dana 61 also uses 3.5" axle tubes. Numbers stamped into the long tube of the axle housing are often faint and hard to read. Here's a Dana 44 front differential below, a G2 Front Dana 44 Assembly, Part D44TJFA456. It is a 6 digit number, typically starting with a 6, stamped into the axle tube just to the right of the diff, when looking at the cover. The KC code identifies it as a 1974 rear axle assembly with a 3.08:1 rear gear ratio. It is 248 on a Dana 60. Ring and pinion gear is 2:65 I think it not 100 percent If we go to the Dana Part Identification Page, we see that this axle is from a Ford F250/350 SRW (Single Rear Wheel – Non-Dually) 4×4.The results can be seen HERE.. • Use this book to order parts for your Dana® Spicer® Axle. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. The information included covers the differential carrier assembly, axle housing, axle shafts, shift system and … If desired, you can then note the numbers from the table (e.g. The amount of revolutions of the driveshaft/yoke should be equal to 1 of the above numbers. The Dana axle identification BOM’s are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Assuming the axle is original the 3/4 tons came with a dana 70 if automatic, a hybrid dana 80 if a 5 speed. The 1964 serial numbers are found on the bottom of the carrier. Using the VIN number for the image above I will now demonstrate how to decode the caravan VIN number. New or Hot Selling Items. Country or origin 2. The specification number assigned to the axle build by Spicer. The number 605234-1 is the CHAPTER 2: AXLE ENCYCLOPEDIA The OE Axle | The Aftermarket Axle | Axle Identification by the Numbers | Determining Axle Ratios and Traction Aids | When All Else Fails | Chrysler Codes | Dana Codes | Ford Codes | GM Codes | Jeep/AMC Codes | Toyota Codes Axle Encyclopedia. Can you identify my axle with brand and year? • … The tag is located on the diff carrier. AAM 9.25; AAM 10.50 (new style)/11.50 Rear; AMC-20 Rear; Chrysler 7.9/8.0 IFS These identify numbers and letters are they for axle tube. Each Dana 60 has a build date and bill of materials numbers stamped into the back of the passenger side axle tube. The Dana 60 is a Salisbury-type rear end; the carrier removes from the rear of the axle via a tin cover. The axle tag typically has two lines of numbers and letters stamped on it. The casting number on a Dana 50 is 229. Order before 4PM and most parts ship out the SAME DAY! It doesn't taper on a Dana 60 and stays 1.5 inches all the way into the carrier. Mar 26, 2005. The top line typically starts with a three-digit axle model code (or the prefix of the part number), followed by a dash, and then the suffix. • These axles will be found with a number of different Axle Shafts, on the basis of OEM specification. I noticed that it was stamped with what appears to be an 81 date code. The part number may also appear on a metal tag attached to the cover plate by the cover screws, depending upon the requirements of the vehicle manufacturer. The format has changed over the years but mostly follow this sequence:. The 1/2 tons (D/W 100 and 150's) are basically the same on axles as the RC's. 5. The numbers on the bottles all relate to the thickness of the oil at certain temperature thresholds. The front is an AAM 9.25 and the rear is a hybrid AAM 10.5 with the larger axle shafts from the AAM 11.5. Hence, the birth of the Dana 61, which has a different casting that moves the pinion over 0.25"-0.437" (conflicting reports) - this allowed for a 3.07 axle ratio. I was under the impression that it came from a GM 3/4 ton vehicle. ALL ton trucks came with the dana 80. The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. Nov 17, 2014. West Coast Differentials stocks a complete line of light duty axle parts for Chevrolet, Chrysler, Dana, Ford, GM, Jeep and Toyota and more! The Dana LMS™ Hub is available on the following Steer and Drive Axle Models: Steer Axles: E-1000I E-1202I E-1462I E … The axle model identification. 3/4 tons (D/W 200 and 250's) usually have a Dana 44HD up front but may have a Dana 60. The differential axle bearings are: LM 104912 (Timken cone), and LM 104949 (Timken cup), (Chrysler numbers 2852729 and 2852728). Axle Identification. Later-model Dana axle identification charts may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1. The Bill of Materials (B.O.M) number is stamped on the right or left hand tube of the driving axles and with the help of a Spicer catalog you should be … The axle bearings are: 25590 (Timken cone), and 25520 (Timken cup), (Chrysler numbers 1790523 and 696403). For easier identification of the engraved, 8 9 THE ULTIMATE DANA 44™ FRONT AXLE for the JEEP® WRANGLER® JK Engineered for all Jeep® Wrangler® JKs, 2007 to 2018, Ultimate Dana 44™ front axles feature a number of upgrades designed for added durability on the trail. Throughout the manual reference is made to certain tool numbers whenever special tools are required. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. The Bill of Material number may also be found on the carrier in some models as shown in illustration (2A). Single Drive Axle Tandem Drive Axle The gear ratio of the axle. The only numbers I get are 42835 and RM 3 on the top of the rear diff. There are only six identifying part numbers relating to a true 8 3/4-inch rear. 4 - OEM part number assigned to the axle build Axle Shaft Rear Dana 35 Driver Side 03-06 Wrangler ABS and Rear Disc $167.95 +Free Shipping There are only six identifying part numbers relating to a true 8 3/4-inch rear. The information included covers the differential carrier assembly, axle housing, axle shafts, shift system and … Dana Spicer and Ford Differentials can be identified most accurately by the tag number or axle tube stamp. The Dana Power-Lok can be recognized by its bolt-together assembly, bolts around the side opposite the ring gear, and multiple openings exposing the cross shafts. This information will help to locate information in this book and to identify the correct parts for servicing. From the highway to the high country, the Ultimate Dana 60 ®, Ultimate Dana 44™, and Dana 44™ axles are bolt-in axles that will stand up to whatever you dish out.With Dana’s innovative Crate Axle Program, it’s easier than ever to get the exact OE-quality axle you need. *** The B.O.M. Model Identification Drive Axle Parts Identification Axle Housing Axle Shaft 1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. recently bought a rear axle from a dodge 2500, thought it was a dana 70, but a found the number 80 on the pumpkin. Dana Axle ID There are multiple ways to positively identify a Dana axle, even if it has been separated from the donor vehicle. • Axle Model Identification, Part Number and Serial Number are located on a tag at the axle centerline. Introduction: The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of vehicles. Axle Assembly Identification Dana/Spicer Products - Rear Axle Codes 1961-1971 : NOTE: The codes listed on these pages only go up through 1971. 4. Still stock with a built transmission at 120k. Here is a axle identification chart. it has a spicer transaxle model 4360-212CH and the input shaft bearings had gone bad, chewed up the top case a little. Dana 60 Front Axle – Exploded View Images presented for reference and educational purposes only. 2. They are used herein for customer convenience only. Quantity: 1.8L (3.8 pints) Rear Differential F-250/350 (10.50 inch axle) Type: Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant. You didn’t identify the number of bolts on the cover. The axle tag typically has two lines of numbers and letters stamped on it. Differential & Axle Parts Specialists We have your differential parts in stock ready to ship today. The GVWR was 10,000 lb. The Bill of Materials (B.O.M) number is stamped on the right or left hand tube of the driving axles and with the help of a Spicer catalog you should be … The model number and date are self explanatory. The Dana 30 gear ratios are either 3.21 or 3.73. Rear Axle Numbers The third major drivetrain component, the rear axle/differential, like the engine and transmission, was also marked for identification. Identifies all component parts of the axle including special OEM requirements such as yokes or flanges. The easiest way to ID a Jeep axle is by looking at examples of the cover shape. 75 in - Kit. Pinion depth is adjusted by adding or subtracting shim thickness. 3. Drive Axles 1 - Country or origin 2 - Axle model identification 3 - Specification number assigned to the axle built by Spicer. 1980 to 1985 would have a Dana 60 or the very rare Chrysler 9 1/4 HD 8-lug rear axle and a Dana 44 HD frontend with manual or auto hubs. I think the dana axles have the model number cast in the housing somewhere. Spicer Axle Parts Book 2 Spicer Axle Parts Book Corporation, presents this Parts Book as an aid in the identification and procurement of replacement parts for Axles. Get What You Know. This axle is ident.ified with 1/8" (3.17 mm) high stamped numbers. Rear Axle Assembly Codes The rear axle ratio may be determined by finding the two- or three-letter serial number prefix in the following table. Using a metal scraper will typically reveal the numbers most easily. This page contains Cherokee, Wagoneer, and Comanche Axle ID Numbers as well as drawings and pictures (where possible) of the axle housings to help you identify which axle / differential came on your Jeep. Axle Shaft Rear Dana 35 Driver Side 03-06 Wrangler ABS and Rear Disc $167.95 +Free Shipping Locate the axle ID tag on the rear-end housing---usually a sheet-metal tag bolted to the housing, although some vehicles had a paper tag, which may be missing. The axles are manufactured by American Axle & Manufacturing, Inc. The chart below identifies Dana Axles used in Jeeps over the years. To download or view any of the service and parts manual section PDFs, simply expand the section you’re interested in by clicking on the red plus icon, then click on the section number in the left hand column next to the item description. thanks This information will help to locate information in this book and to identify the correct parts for servicing. Item: 52302.101.14 MFG#: 5-260X Most axles since 2001 have an identification tag or engraved serial number or lot number on the axle beam. This information will help to locate information in this book and to identify the correct parts for servicing. An axle ID … The posi manufacturer codes are D for Dana, E for Eaton, and W for Warner. This information will help to locate information in this book and to identify the correct parts for servicing. The axle is also much larger than my dana 60. Compared to a GM 10 bolt axle (for example), a semi-float 14 bolt is a nice upgrade. Axle Model Identification, Part Number and Serial Number are located on a tag at the axle centerline. DRIVE AXLES DRIVE AXLE ASSEMBLY TAG 1.
Albertsons Rewards Card, Army Training Center In Kathmandu, Is Randall Cunningham Still Alive, Does Ronaldo Sleep At Night, Nova Festival 2021 Adelaide, Largest Employers In Columbus, Ohio, Giving Opinions Esl Lesson Plan, Uv Resistant Zip Ties Home Depot, Justin Bieber Vmas Outfit 2021, Were Millwall Ever In The Premier League,